• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Go About boarding up doorway Up a Door

Boarding up a door is one way to protect vacant investment properties from the elements. While it won't prevent all destruction, it can help avoid certain problems that come with severe storms.

The boarding up doors of doors and windows can also deter burglars and vandals. Installing plywood panels over openings can be costly and time-consuming.

Take a measurement of the door

First, you'll need a tape measure. You might want to keep a chair or ladder nearby in case you need an improved view of the top of the frame. If you must use these tools, be sure to wear gloves and safety glasses.

Once you have the measuring tool, begin by taking the door's width measurement. You can do this by running the tape measure horizontally across the door. Make sure to remove any other parts of the door, for instance a sweep, before measuring. Then, determine the height measurement by measuring up from the floor to the sill plate or lintel. It is crucial to take measurements in several locations, particularly when measuring older doors as they may not have an exact rectangular shape. If the measurements are different take the largest number.

After you've logged the width and height measurements, you'll need to determine what size emergency boarding up service you need for the frame. It should be at a minimum 2 inches wider and 1'' higher than the door. 2'' higher. This will allow plenty of space to shim the frame and door to fit.

It's a great idea remove the trim or casing around the jambs of the door in order to observe the studs. This will allow you to determine the exact measurement of the gap between the studs and the edges of the frame.

After you've removed the trim, you'll be able to determine the width of the frame of your door by running the tape across the entire frame in three locations and using the smallest measurement to determine the width of your door. You should also determine the height of the frame from the top to bottom on both sides, and then use the shortest measurement to determine the height of your door.

If you're having difficulty with the measurements, you should consult a professional to come to your home and do the measuring. They will be able to tell you exactly what type and size of door you need and how to prepare the frame to accommodate the door you want to buy.

Plywood can be cut into pieces

A door frame is generally comprised of a set of thin boards or studs that create a hollow space surrounding the door. Two hinges are connected to the studs and keep a typical door in place. If you want to finish doors, you'll need to remove it from its hinges overnight. Placing plywood into the door's opening is a simple way to board the door and keep insects from gaining entry into the home. It's easy to do this without having to nail or screw the plywood onto the frame of the door.

Plywood is easy to work with, inexpensive and looks stunning when finished. This makes it the ideal material to provide an interim solution to an issue that requires the removal of the door that is in use and refinishing or installing a new one. It can also be used to secure the opening of a room being transformed, such as an excavation site or basement.

For a wall constructed of plywood begin by taking measurements of the width and height of the door opening. Note the measurements on the plywood using a utility knife and a drywall square or another straight edge made of metal. Then, snap a chalkline across each line to mark the area to cut. Utilize a circular blade to cut the plywood to the desired size.

When cutting the plywood, it is crucial to shield your ears and eyes. If possible wear protective goggles and earplugs while working. In addition, it's crucial to use a knife with a lot of teeth that can cut quickly and with less tear-out. Utilize a small piece of wood to guide the blade. Hold it about a hair's width away from the mark when cutting.

A great way to hold the plywood in place without screwing it to the studs is to attach two braces at each end. Set one brace on the inside of the door and the one on the outside. Position a pair 1-1/2-inch deck screw in each hole, and then tighten by using an open-end ratchet.

Fix the Plywood

When you have a piece of plywood cut to the appropriate dimensions and with the holes for stiles and rails predrilled and ready to fasten the panel to the frame. This is a relatively straightforward project that does not require a lot of carpentry expertise, as long as you follow the correct procedure and use the appropriate tools.

Set up a table near the doorway with two sawhorses at each end, and framing lumber 2x4s. Use the marks made during the measurement procedure to guide you in cutting the plywood. Utilize a utility blade and a metal straight edge to score the lines. This will serve as an outline for the saw blade and to prevent splintering during cutting the plywood.

Wear eye protection and cut along the lines of scoring using a circular or table saw equipped with a fine-tooth blade. Then sand the edges of the plywood panel with 120-grit sandpaper. This will smooth out the panels and remove any burrs from the saw cuts. After sanding, apply a layer of wood sealer to the plywood panels, and let dry as directed by the manufacturer.

Install the hinges on the door frame. If you're using a T-hinge drill holes on the outside edge of your door to allow for the straps of the hinges. Then, you can screw the hinge on the outside to the frame using the screwdriver. Repeat the procedure for each hinge on the inside of your door. Be careful not to tighten them too much or the door may shift.

If you have a single T-hinged outside door it is possible to make it easier for the latch to close by placing wire through the loops of the exterior hinges. Fold a piece of connect wires in half and then fish it through the two holes on the exterior of the door. Then, you can twist the wires and secure the door.

Install the Plywood

With the measurements you made using the measurements you took, put the plywood in the door opening. Move the header (top) of the frame and the sill (bottom). Use a level to make sure there's not any slop in the header or sill. If it's not perfect you can place a second shim wherever required and repeat the process until the sill and header are level.

Once the plywood is inside the frame, secure it using stainless steel hinge bolts and wing nuts. Make use of a screwgun that has a hex head attachment to avoid removing the screws' heads.

If your home has studs that run along the length of your doorway, you could drill hanger bolts into every framing piece. This is a far easier job than making the hole using the drywall saw.

After putting the plywood in place take measurements of the width and height of your door opening. If necessary, cut your bottom of the plywood to be a little higher than the height of the door frame. Cut two pieces of framing lumber 1 by 6 as braces for the upper and lower ends. Put on eye protection and cut along the lines drawn on the plywood with circular saws fitted with a fine-toothed blade. Take any splinters out of the cuts by using an the sanding block.

Once you've got the two braces in place attach each one to the plywood with a pair of finishing nails that measure 2 inches. Once you're done counter-sink the heads of all nails. Make sure to seal the braces and the plywood with a high-quality wood sealer such as this wipe-on polyurethane by Minwax.

If the door is too big for your doorway, you can add some decorative molding to fill in the space between the door and jamb or you can resize the opening. In many cases it is less expensive and simpler to purchase a new door. It also eliminates any issues that you might have experienced with your door's original model in the event that it was damaged or not suitable for the opening.