• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Most homeowners can repair hinges that are loose. If the holes for screws are shattered and do not hold screws, you could need to use dowels and wood glue to put back in the door hinge.

Remove any surface that has rust. This will help to keep the dowels in their place and provide a solid base to hold onto.

Removal of the Hinges

Many standard door hinges are removable, which makes it easier glass to glass hinges move the door hinges repair from one side to the other or take the entire door off the frame, if needed. Anyone with a little patience can remove the hinges but you need to know what to do.

If the hinges have been painted, you'll need to remove it prior to trying to remove the pins. If you don't, the paint could peel off and scratch the door when you attempt to lift it. To break the seal of the paint put the hinges into a stainless steel pan and fill the pan with water until the hinges are fully submerged. Let the hinges sit in the pan for around 30 minutes. The heat of the water will soften the paint making it easier to take off.

Once the pins have been loose, remove the hinges and the frame from the door. It is possible to use a standard screwdriver, but you should use a magnetic screwdriver for this project. This type of screwdriver was designed to remove screws made of metal and can make the work run much more quickly.

Before you attempt to remove the hinges, it is a good idea to spray them with lubricant. A simple lubricant will help the process move along quickly and aid in the removal of the pins and screws. You can find this kind of lubricant at a variety of hardware and home improvement stores.

The number of hinges needed will also differ based on the type of door you have and the way it's set up. Solid-cored and heavier doors will require more hinges while hollow-cored doors that are lighter may only need two or three.

Understanding the different types of hinges will help determine which one is suitable for your needs. The hinges on the exterior are designed to hold the weight of a patio door hinges, but interior hinges must be able support lighter loads.

Reattaching the Hinges

Over time, the hinges of doors may lose its grip and then begin to slide or hang crookedly. It can be a big issue, but the solution is usually easy. In most cases an easy tightening of the screw will fix the issue. However when the screw holes are ripped out, this can be more difficult to do. However, there is a trick to get these holes back to their original size that utilizes a wood dowel.

Begin by drilling the hole using a drill close to the new screw size (normally 3/8"). Fill in the hole using wood glue and a wooden stick. The dowel should be cut to a length that is exactly the same as the screw to ensure a snug fit. Install the screw again and tighten it until you are satisfied with the degree of tightness. If the Hinged Door Repairs is still unable to be bounded up, you can insert another dowel to the gap. Repeat the process. Close the upvc door hinges slowly after each adjustment to ensure that the perimeter clearances are correct.

You could also use a wood plug instead of the dowel. It's also possible, but may take some time to set up. You can use the wood piece that has been whittled to the proper size. If you don't have a tool for woodworking you could also try using toothpicks or wooden matches.

Use a countersink to make the hole smaller for the head of screw after you have installed it. This will prevent the screw from hitting the edges of the doors when they are opened and closed. This will aid in tightening the screw when reinstalling the hinge.

After installing the hinge, apply lubrication to the hinge using an oil-based lubricant that is dry. This will prevent it from becoming stuck in the future. You can use products such as PB Blaster and Liquid Wrench. Apply a thin coating and allow it to soak into the hinge barrel for about 15 minutes.

Refinishing the Hinges

If you're not ready to replace hinges, you could try a few simple fixes. The first step is to ensure that the screws holding the hinge plate to the frame and door are tight. If they're loose, tighten them using the help of a screwdriver or a power drill. Be careful not to tighten your screws so tight that they start to create gaps in the trim joints or, even more damagingly, strip the threads.

If the issue is that the hinge plates are splitting and you want to reattach the plates by applying wood glue on the back of them and inserting toothpicks or wooden dowels into the holes. The toothpicks or dowels will serve as a solid base for the screws and keep the plates from moving when you drive them into position. Allow the glue to dry before reattaching the hinge.

The screws could also be smashed or gone. This can be fixed by replacing the screws with larger ones. Make sure you use the correct drill bit for the size of the screw hole in order to avoid drilling into other parts of the jamb or hinge.

Close the door once you've reattached your hinge and check the gap between the frame and the door. It should be approximately the thickness of one nickel all the way around, or less if there's an existing gap that was caused by a door that was not properly hung. This shouldn't be a problem as long as the hinges are correctly installed.

If you notice that the hinges are still loose, you can try adding a thicker hinge shim between the hinge plate and the mounting surface to add a little extra space. You could also try taking the hinge pin from the troublesome hinge and pounding it with a hammer in order to make it more secure or using a new hinge pin altogether. You can also lubricate the hinges using mineral or jojoba oil to lessen friction and assist in keeping their place. Lubricating your hinges periodically will help stop them from becoming stiff and squeaky and can also prolong their life.

Cleaning the Hinges

The friction generated by the hinge's constant motion attracts dust particles. These particles can get stuck and accumulate over time in the moving parts of door hinges if they are not regularly cleaned and lubricated. The hinge will get stiff and creaky and its appearance could rapidly diminish. Regular cleaning, lubrication and inspections will maintain the quality and function of hinges on doors.

Examine the hinges for signs of the accumulation of rust. If the rust is so severe that it has damaged the surface of the screw holes or the barrel of the hinge, you'll have to replace the hinges. If you can save the hinges, first brush off any loose rust with steel wool and a wire brush. Apply a commercial rust-removing product or a homemade solution such as lemon juice on the double glazing window hinge repairs. Allow the rust-removing solution to be on the hinges for several minutes in order to penetrate and dissolve any remaining rust.

If you don't want to spend the time and money to replace your hinges, simply retightening the screws will make the hinges functional again. If you've sanded the screw holes however, it might be necessary to add a wooden dowel or shim to the hinge. Wooden dowels come in round rods of various lengths and sizes. They can be purchased online, in stores selling woodworking supplies and home improvement centers.

You can also make an shim using made of plastic or metal depending on the type of hinge you are using. To make a dowel, you need to cut a dowel from wood to the desired length. You can then dip the dowel in a glue for carpenters and then insert it into the stripped hole and let the glue hold the dowel in the right position.

Before you begin cleaning the hinges, place down a paper or cloth towel to shield flooring and other surfaces from spills and drips that may happen. After the area is secured and dry, clean the hinges using a soft cloth or sponge coated with a mild cleaner or vinegar to eliminate built-up dirt, grime and tarnish. You can make use of a small or toothbrush brush to get into difficult-to-reach areas in tight spaces and crevices.