• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Door lock change is a simple and affordable method to increase your home's security. However, this procedure is not for everyone. It requires a certain amount of skill and patience.

It is necessary to replace the cylinder, which is located within the knob's body. The cylinder recognizes the key when it is inserted into the lock.

Removing the old lock

The first step is to remove the lock you have been using for a while. It is a fairly easy process, but you must keep some things in mind. Make sure that the new lock fits the door. This will ensure that it fits properly and does not leave a gap in the deadbolt plug or latch.

Once you have removed the latch plate, look for two bolts or screws on the inside of the casing that connect the casing and two halves of the lock together. Take these screws off using a screwdriver before removing the lock from the door. If you have a mortise locking system, there is a set screw that holds the handle to the spindle. Use a screwdriver to remove this screw, then remove the doorknobs.

Remove the deadbolt as well as the latch plug from your door jamb. Install your new lock. If you are replacing a mortise lock, you should also measure the distance between the lock case and the door's edge to ensure that your new lock will be able to fit.

Many reasons could cause you to change the door lock, such as believing that someone else has the key or welcoming an incoming roommate. In any event, you could save money by taking the lock off yourself, rather than hiring an expert to remove it. It is much easier than people think and can be completed in a matter of a few minutes.

Remove the trim and handle from your door. Then, pry the trim loose with a flat screwdriver. You should be able to twist off the majority of it. In certain cases you might be able to remove the handles completely. Next, examine the handle for a small pinhole on the interior side and insert a straightened paper clip into it. This will activate the release mechanism, allowing you to remove the handle. Then, look for a small tab in the interior of the double glazed window and door lock repair lock mechanism replacement (great site) and push it using a flat screwdriver. Once the spindle has been removed, you can then remove the housing and cylinder.

Selecting a new locking system

There are a lot of options available when it comes to selecting the right lock. Think about the various kinds of locks and select one that is in keeping with the style of your door. Take into consideration the backset which is the distance between the edge and the center of the hole for the lock. Also consider the cross bore, which is a small hole in the middle of your door frame. Select a lock that will fit the door thickness and the swing.

Most door locks have been assessed by BHMA and the American National Standards Institute to provide you with an idea of how they stand up to use and how difficult they are to disable or pick. A grade 3 lock may be the best choice for a peaceful rural apartment complex, while an entry grade lock could stand up to the traffic near a busy storefront on a busy city street.

Most smart door locks require digital code to open. If you are worried about hacking, or any other security concerns, consult a professional locksmith.

replace upvc window lock the cylinder

If your door lock's cylinder is damaged or broken it can be replaced in a matter of minutes by completing a do-it-yourself project. It is important to select the appropriate cylinder and follow all instructions. First, remove the knob or handle if it is present. Then with a screwdriver unscrew the trim that surrounds the lock cylinder. After the trim is removed, you can remove the screws that hold the cylinder with a flathead. The cylinder is then gently lifted out of the door.

Before you install the new cylinder, be sure it's the correct length for the door you are using. With a tape measure, measure the distance between the cylinder's center and its left and right side. Then, buy an additional cylinder using the same measurements. This will stop cylinders from snapping when doors are kicked or the key gets stuck inside.

Once you have a suitable replacement locks for double glazed windows cylinder, insert it in the door and turn the key. This will align the cylinder with the carriage which is located usually on the outside of the lock. You can then loosen the set screws that should be a couple of turns in the head. If there is a screw on the outside of the case that is holding the door, you will have to loosen it.

You can replace the lock cylinder you have used with the new one by inserting it into the case and then tightening the set screws. Reinstalling the piece that connects the cylinder to the stem of a lock indicator is also essential. This can be done by pulling three small tabs on the back of the cylindrical with needle-nosed pliers. Attach the smaller bracket to the back of the cylinder. You must then install the strike plate and latch plate, along with the retaining rings attached to the top of the lock cylinder.

Installing a new lock

Begin by measuring the door's width if are replacing an existing lock. Most locksets for residential use come with a thickness of 3/8 inch to 1 3/4 inches. If your door is more than 1 3/8 to 1 3/4 inches, you'll require an extra thick door kit. This will include longer screws as well as an extended spindle extension or tail piece for door knobs.

The majority of locks come with a detailed installation guide to assist you. Before beginning, you must read the instructions to ensure that you have followed all the steps. The booklet will give you a clear idea of the level of skill that is required to complete the task. You may want to ask a friend who has experience changing upvc windows locks repair for help if you are changing a lock the first time.

It's a good idea to tape the openings in the old lock before installing the new lock. This will stop the screws from falling through the holes, and also protect any tiles you have installed. This will also protect your tiles from any damage caused by dirt, rust and grime. SECURAM Touch comes with a piece of painter's tape that is intended to be used for this purpose, however you can also use gaffer's tape or masking tape in the event that you have it.

After removing the screws that hold the lock's inner half to the exterior and pull the lock straight away. This must be done quickly to avoid the lock from closing accidentally and harming the mechanism.

Fit the new latch bolt in the upper cross bore of the new lock, if it comes with one. Be sure to put it in the correct position that is usually indicated by an arrow on the faceplate. Then, you can screw the latch plate onto the bolt.

Finally, screw in the deadbolt and strike plate to the door jamb. Test the deadbolt by throwing it a few times to verify that it extends all way through the strike plate and is secured. If you're using an electronic smart lock, be certain to follow the instructions to program it. This requires downloading an app, creating an email address, confirming your identity, then accessing the wireless network to add your device.