• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons to Change Door Lock

There are a variety of reasons to change your the door lock, from improving your home's security, to redecorating your entrance. You may also need to change locks if the key gets stuck or is difficult to turn.

Even DIY beginners can easily change their lock. Begin by gathering the necessary materials.

Remove the lock from the old one.

The removal of the old lock from the door is a necessary step prior to installing the new lock. This is particularly important when you suspect that someone else has access to your home. It is also an ideal option if you have moved into a new house, experienced a break-in or received a new roommate. The process is a lot simpler than you think and can be completed in a few minutes.

Start by removing the screws that secure the deadbolt faceplate on the frame of the door. You'll need to take off the screws on both sides of the door to take off the faceplate. This will allow you to observe what's behind it and will give you a better idea of how to proceed with the remaining steps.

Once you have removed your old faceplate, you will need to remove the bolt and strike plate. Remove the bolt from the door hole by using the screwdriver. If the bolt is rusty you may have to use a chisel to hammer it out. If you're using a chisel, you must be cautious not to scratch the door frame.

Before you take out the lock that was previously in use, make sure that the new deadbolt and doorknob will fit in the existing holes in the door. Most hardware stores and big box stores carry several different types of locks and can help you find the right one for your requirements. If the lock you purchased doesn't match your door, take it back and seek assistance.

When you're removing the old lock, search for small slits or depressions in the handle or around the trim. If you find them, insert a straightened safety pin or flat screwdriver into them to open the handle and expose the screws beneath.

Once the screw inside the handle is removed, you can begin removing the knob from its spindle. To do this, locate the set screw at the base of the knob and loosen it. Then, remove the spindle.

Install the new lock

It's a good idea to change locks on doors throughout your home regularly, especially in the event of a burglary or you move into a new home with roommates. It's easy, affordable and efficient to change the lock on your door. With a screwdriver, and a few simple instructions most people can do it themselves. Depending on your situation you may be interested in learning how to reset a lock to ensure that you only have the key.

You'll need to buy a new window lock repairs with the same keyway as the existing lock. You will save money if you modify the lock yourself. Most locksmiths charge extra to do this. You can buy the new lock at a hardware store or online. A standard deadbolt will usually be able to fit on doors of all sizes however, you'll have to measure the area on your door to ensure that it fits.

The majority of the time, your new lock will come with an image of a cardboard model that shows how it will fit on the door. You can use it as a guide when drilling the hole, which is much easier than measuring each time. If the template doesn't match your hole, take it back to the store and request a replacement Window Lock.

When installing the new lock, be sure to place it on the right side of the door. You can confirm this by inspecting the latch, which must be labeled "up" or something similar. Make sure that the latch is seated correctly in the plate and fix it using the supplied screws.

When replacing a knob lock be sure to pay attention to its handing. Certain knob locks are left-handed. If you're not paying attention, the knob could be installed on the wrong side of your door, which will make it impossible to lock from the inside or outside.

After you've finished testing the new lock to confirm that it's working. You should be capable of locking the door from both the inside as well as the outside, and unlock it using the key. If you aren't satisfied with the outcome, you can contact an expert locksmith to repair it.

Test the lock

A door lock that will not open is a nuisance however, it could also put the safety of your family at risk. It's easy to solve the majority of door lock problems by conducting some troubleshooting and lubrication. Make sure that the key is properly cut, and that the lock assembly is not loose or dirty. If this doesn't solve the issue, try lubricating your door lock actuator using graphite powdered with powder.

Check that the door lock switch, the wiring harnesses and the actuator connector are all working properly. To do this, consult the manual or wiring diagram to determine the purpose and color-coding of all the door lock switch wires. Utilize a digital meter or test light to verify that the actuator is receiving power and is grounded when the switches are turned on. If you see the switches switch on and off with voltage this means that the switches are in good condition and the actuator is likely to need replacing.

If the switch seems to be working but the actuator doesn't move when you turn the knob it could be an issue with the actuator itself. The actuator cylinder is loaded with spring pins that keep the cylinder from moving until the key is inserted, which it pushes the pins up to match the key's height at the point of entry. The cylinder will then begin to rotate, opening the lock body, allowing the latch to open for the handle.

If your door lock actuator is faulty, you can remove the switch and wires from the actuator by using a small screwdriver to release the locking bolt and remove the plastic cover that houses the electrical connector. Then disconnect the door lock actuator, and let it fall. You should be able to find the two bolts in 10mm that keep the actuator in place, and remove them. After the actuator has been removed, you should be in a position to disconnect the black electrical connector and then pull it out along with the lock and actuator assembly.

Replace the key

If you have a keyed door knob or deadbolt, if it is not working properly you need to either rekey the lock or replace it completely. It is not difficult to do this yourself and can save some money. It is recommended to hire a professional locksmith check the locks for any issues before you start. This will give you peace of peace of mind knowing that your home is secure and safe.

To begin, take off the faceplate that is on the outside of the doorknob or deadbolt. If there are screws holding the faceplate in place then use a screwdriver to pull it off. Then, remove the interior faceplate using a flat-head screwdriver. After you have removed the faceplate, you can remove the bolt and screw from the lock cylinder.

A locksmith can tell you whether you require a replacement window lock or rekey the lock. They can also give you advice on the best security options for your home. They can also make the necessary adjustments to your door and frame for the perfect fit. They also offer an assurance on their work.

If you decide to rekey the lock you'll have to first buy a new key for it. It is crucial to use the correct key in the lock. Using an incorrect key could damage the internal mechanism and prevent it from working. Insert the key into the lock to verify its size. If it is perfectly with the plug, it's the correct size. If the pins extend from the top of the plug, then they are too long.

You may need to change the lock on your door for a variety of reasons, including:

Rekeying a lock can be an affordable alternative to replacing it if you are moving into the home of an owner who has passed away or if keys have been lost. It can also be less costly than a full replacement window lock. Rekeying an existing lock might not be feasible in some circumstances. For instance, if the lock is damaged or has been repeatedly jammed, it's probably the time to replace it.