• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Go About Boarding Up a Door

Boarding up a door is one method of protecting vacant investment properties from the elements. It's not guaranteed to stop all damage but it can assist to prevent some of the problems associated with severe storms.

The idea of boarding up service near me commercial boarding up service doors and windows can deter trespassers, vandals, and squatters. However, it can be expensive and time-consuming to install plywood boards over the openings of a property.

Measure the Door

The first thing you'll require is an accurate tape measure. You may want to keep a ladder or chair nearby in case you need an improved view of the top of the frame. Wear gloves and safety glasses when you use these tools.

Once you have the measuring tool, begin by taking the door width measurement. This can be done by running a tape measure horizontally along the door. Be sure to eliminate any extra door parts like a door sweep, from the measurement. Next, take the height measurement by measuring from the floor to the existing sill plate or the lintel. It is important to measure multiple places especially for older doors, because they may not be a perfect rectangle. If the measurements are different, use the largest number.

You'll have to determine the size of the frame once you've taken measurements of the length and width. It should be at a minimum 2 inches wider and 1'' taller than the door. 2'' higher. This will give enough space to shim both the frame and frame to fit.

When you're ready to measure the door frame's width and height measurements, it's recommended to remove any trim or casing around the door jambs so that you can see the studs that are behind them. This will help you to determine the exact size of the gap between the studs and the edges of the frame.

After taking off the trim, take a measurement of the width of your door frame using the tape measure. Measure the frame at three different points and then use the most compact measurement. Also, you should measure the frame's height from top to bottom on both sides. Make use of the shortest measurement to determine your door's width.

If you're having trouble with these measurements It's a good idea to consult an expert and have them visit your home to take the measurements for you. They will be able to give you the exact kind of door and size you need and the best way to prepare the frame to accommodate the door you want to buy.

Cut the Plywood

A door frame is usually made boarding up door of a series thin boards or studs that create a hollow space around the door. A typical door is held in place by two hinges connected to the studs. If you are looking to refinish a door, you will have to take it off its hinges over night. Placing plywood in the door opening is a great method to board a door and prevent insects from getting into your home. It is simple to do this without the need to nail or screw the plywood onto the frame of the door.

Plywood is cheap, easy to work with and looks great when it is completed. It is the ideal material to use as a temporary solution for situations where you need to remove an existing door in order to refinish it or put in an entirely new one. It can also be used to protect the opening of a room being transformed, such as an excavation site or basement.

Start by measuring the width of the door opening and the height. Note the measurements on the plywood using an utility knife and a drywall square or other metal straight edge. Next, snap the chalk lines across the lines you have marked to mark the areas you want to cut. Then, use a circular saw to cut the plywood into a size.

When cutting the plywood it is important to protect your ears and eyes. If you can wear eye protection and earplugs as you are working. Additionally, it is essential to choose a blade that has a wide range of teeth that can cut quickly and without tear-out. To minimize the chance of cutting pieces of wood from the edges of the cut using a small piece of wood as an example to guide the blade and hold it at a distance of just a hair's width away from the line while cutting.

A great way to hold the plywood in place without screwing it to the studs is by fixing braces that are short at each end. Put one of the braces on the inside of the door and the one on the outside. Then, insert the deck screws in each of the holes and tighten them with an open-end wrench.

Fasten the Plywood

Once you have a sheet of plywood cut to the proper size and with the holes for stiles and rails predrilled, it is time to fasten the panel to the frame. This is a simple task that doesn't require advanced carpentry skills, as long as you use the right tools and follow the correct procedure.

Start by setting boarding up and burglary repairs a table near the doorway with two sawhorses and 2-by-4 framing lumber at each end of the table. Lay the full sheet of plywood flat atop the sawhorses and use the marks made during the measurement process as a guide for cutting. Use a utility blade and a straight edge of metal to score the lines. This will act as a guide for the saw blade and also prevent splintering of plywood when you cut it.

Wear eye protection and cut along the scored lines with a circular saw or table saw fitted with a fine-tooth blade. Sand the edges of the panel with 120-grit paper to smooth it out and remove any burrs. After the sanding, apply a layer of wood sealer on the plywood panels and let dry according to the instructions of the manufacturer.

Install the hinges onto the door frame. If you are using a T hinge, you need to drill holes through the outer face of the door to accommodate the strap portions of the hinges. Then, screw the outside hinge to the frame with the screwdriver. Repeat the procedure on the inside of the door for the hinges remaining, being careful not to overtighten one of them or the panel may shift.

If you have only a single hinged outside door, you can make it easier for the latch to close by fishing a wire through the loops of the exterior hinges. Bend a piece of tie wire in half and fish it through each of the two holes on the outside of the door, then twist the wires together to tighten them and secure the door.

Install the Plywood

Place the plywood in the opening of the door according to the measurements you made. Move the header (top) of the frame and the sill (bottom). Use a level and make sure that there is no slop between the header and sill. If the level isn't perfect you can put another shim in the area needed and continue this process until you have the header and sill to be level.

Once the plywood is inside the frame, secure it with the stainless steel hinge bolts and wings nuts. It is a good idea to make use of a screw gun with an attachment for a hex-head to prevent stripping the head of the screws.

If you live in a house with studs running along your doorway, it is possible to drill hanger bolts into each of the framing members. This is much easier than using a drywall cutting tool to make the hole.

After putting the plywood in place after installation, take measurements of the width and height of your door opening. If needed, trim the bottom of the plywood to fit the size of the door frame. Cut two pieces of 1-by-6 framing lumber for braces to connect to the upper and lower ends of your door. Cut along the lines drawn on your plywood using a circular blade with teeth that are finely-toothed. Wear eye protection. Remove any splinters from the cuts using the help of a sanding block.

Once you have the two braces in place Attach each brace to the plywood with pairs of finishing nails that measure 2 inches. Counter sink all nail heads when you're done. Cover the braces and plywood with a quality wood sealer, like this wipe on polyurethane from Minwax.

If the door is still too big for the doorway, you can add an ornamental molding to fill in the gap between the jamb and the door or you can reduce the size of the opening. In many instances, however it is less expensive and more convenient to buy an entirely new door. It also removes any problems that you might have experienced with your original door in the event that it was damaged or no longer fitted the opening.