• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Boarding Up Windows and Doors Before a Storm Hits

boarding up windows and doors up your doors and windows before a storm strikes can provide measurable protection against damage. To do this, you must have a few things in the go.

Measure the height and width of the window including the frame (not the trim or masonry that surrounds the window). Note these measurements so you won't forget.

Preparation

It is recommended to board up your windows and doors before an event like a hurricane or natural disaster. This will minimize property damage and reduce the chance of dying. It requires an enormous amount of planning to build a board around windows. You have to buy and measure plywood boards and you must know the specific dimensions of each window. It also takes time to cut the boards and install them correctly. The process can be streamlined by preparing the boards immediately you hear of a storm approaching your area. You can avoid a stressful rush in the last minute and make it easier for both you and your employees.

Begin by listening to forecasters for weather and following guidelines issued by your local government. The earlier you begin the process the better, as it allows you plenty of time to collect and store the needed materials without feeling pressured by a rapidly approaching storm. You may need a large amount of plywood to cover your windows, according to the severity and speed of the storm. To ensure that you have the right size, you can make use of a tape measure to determine the width and height of each window opening. Be sure to include the framing or trim around each window, as well as any ledges that are extended, if appropriate.

Divide the width and height of your window by 2 to determine the number of plywood sheets you will need. If your window has a width of 16 inches, the thickness of each sheet is 8 inches. If you have an exterior made of wood, you should drill pilot holes into the plywood sheet and align them with the window frame underneath to prevent splitting when you screw into the screws.

If you have a larger window opening than one sheet of plywood is able to handle, cut two sheets of plywood that are half as large as the desired window. Then, place them side-by-side on the wall. Cut a piece 2 by 4 in (5.1 10.2 cm) 10.2 cm) of lumber to the length the connecting edge between the sheets of plywood, and place it on top of the seam. Then, screw 2.25 in (5.7cm) screws into the plywood sheet and into the bracing to join the two.

Materials

To ensure security and safety For your safety and security, only use materials that are sturdy and will not break or splinter in high winds. Plywood is a popular material to board up windows. It is easy to use, affordable, and readily available. Pick plywood that is exterior grade (CDX), as it is more durable and have less knots and warps. A more durable option is storm shutters or hurricane shutters, which are put up over windows that are already in place to provide greater protection against shattered glass and inclement weather.

Once you've identified the location of your windows then measure the width and height of each one to determine how much plywood you'll need. Utilize a power drill to make pilot holes in the plywood sheets around the windows at intervals of two inches. Mark the walls with studs prior to attaching the plywood to ensure that the boards are secured. If your home has wood siding, search for nailheads that might indicate stud locations. You can also use your drill to locate the locations of studs. Be sure to drive the screws into the framing and not the trim or sheathing; a plywood panel fastened only to these materials may become an hazard during strong winds.

If the size of your window is too big for a single sheet plywood, cut two separate pieces that are each half the size you require and join them together with 2 by 4 inch lumber. Label each piece of plywood so that you know which window it will be covering.

Make sure you use corrosion-resistant screws that are long enough to penetrate the sheathing as well as the studs that will be used to join the plywood panels to the wall. To secure the plywood panels to the wall, use screws made of corrosion-resistant that are long enough to penetrate the sheathing and the studs.

In addition to securing your windows, it is also advisable to install a "No Trespassing" notice on the property and think about installing polycarbonate security glass such as DefenseLite over your primary windows. These transparent shields adhere to the existing glass to guard your windows and doors and are virtually unbreakable, deterring criminals from breaking in.

Installation

If you live in an area susceptible to hurricanes, or are planning on moving to one, the best course of action is to secure your windows and doors before the danger of a storm arrives. It's a task that can be accomplished quickly and effectively however only if you make the effort to measure and cut, then label your plywood before the storm comes.

You'll also need a few other tools, including drills (or nails and a hammer in the event that you don't have an electric drill) and tape, a saw, a level, gloves and safety glasses. It's a good idea to coat the plywood with sealant and make it waterproof.

Begin by measuring the window's size and height. Then cut the plywood sheets to fit inside the frames. It's best to do this on-site, as it gives you more control over the exact dimensions of the plywood.

Use a circular saw or track saw to cut the boards to the proper size Be aware that you'll need to sand them off once they're put in. Once your boards are set then screw the 3" stainless steel hanger screws into the posts that frame each window. Use washers to secure each bolt as well as wings nuts. Make sure that each screw penetrates the studs at least two inches to ensure that the board is strong enough to resist high winds.

If you're building using concrete blocks, you can connect the plywood using pan head screws that are galvanized and driven into the overlapping edges of the panels into masonry or cinder block. You'll also have to drill pilot holes into the masonry, and then insert corrosion-resistant screws into the holes. It's a job that could take as long as three hours for each window, so it's essential to begin the process immediately after you hear that a hurricane watch has been issued. This will allow you plenty of time to complete the task before the storm strikes.

Maintenance

If you're a homeowner, or business owner, you must have the necessary materials to board up doors and windows ahead of an extreme storm. This can help you avoid costly repairs and also protect your property from further damage resulting from wind, rain debris, flying debris and other factors that could impact windows.

The appropriate materials can make 24 hour boarding up service near me up easier and quicker. The most important thing is to determine the dimensions of each window you need to cover. This will ensure the OSB or plywood fits snugly and will not be able to slide off easily. If you are using plywood, make sure you use sheets made of exterior grade, and consider adding a protective finish.

After you have the OSB or plywood taken measurements, mark the locations where screws will be inserted into the board. Use a drill to predrill holes at 12-inch intervals in the plywood. This will allow you to safely fasten the boards with hanger bolts during an emergency boarding up near me or in the event of a disaster. After the storm is over and the local authorities have given you the all-clear to go ahead, remove the bolts, but save them for future emergencies.

Then, you can install the plywood panels over the windows. Be prepared to work in pairs. If you're using plywood, ensure that you sand the edges so they are smooth and won't scratch your paint or trim. Then use corrosion-resistant screws to attach the plywood using the pilot holes. If your home is lined with vinyl shingles it is recommended to nail the plywood to the shingles, not the wood framing underneath.

Apart from keeping out rain and other weather elements, a boarding up window is also a good method to stop burglaries. Burglars will target a building with a window that is broken or one that's not locked. They're also more likely to enter a store that's been fenced off than one without. This is something that business owners in retail must take seriously.