• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to fix door hinge a Loose Door Hinge

Fixing a door hinge that is loose can be a doable job for most homeowners. If the holes for screws are shattered and do not hold screws, you could need to use dowels and wood glue to fix the hinge.

Remove any surface that has rust. This will help to keep the dowels in place and provide a solid base for them to rest on.

Removing the Hinges

Most hinges on doors can be removed, which makes it easier to move the door from one side to the next or take the entire door off the frame should it be needed. Anyone with a little patience can remove the hinges, but you need to know what to do.

If the hinges have been painted it is necessary to remove it before you attempt to remove the pins. If you do not, the paint may flake off and scratch your door when you try to lift it. Place the hinges in a stainless steel pot and fill it with water to the point that the hinges are submerged. Let the hinges sit in the pan for approximately 30 minutes. The heat of the water will soften the paint, making it easier to take off.

Once the pins are loose, remove the hinges and the frame from the door. It is possible to use a standard screwdriver, however a magnetic screwdriver is recommended for this task. This type of screwdriver was created to grab screws made of metal and can make the work run much more quickly.

It is a good practice to spray some lubricant on the hinges before attempting to remove them. A simple lubricant can help you move the process along faster and also remove the pins and screws more easily. This kind of lubricant is able to be found in most hardware stores and home improvement shops.

You should also keep in mind that the number of door hinges you'll need will vary depending on the kind of door and the setting. Solid-cored and heavier doors will require more hinges, whereas hollow-cored doors that are lighter may only require two or three hinges.

It is also important to know the various types of upvc door hinges of hinges to determine which ones will best suit your needs. The hinges on the exterior are designed to support the weight of the door however, interior hinges will have to be able to handle lighter loads.

Reattaching the Hinges

Over time the hinges on doors can loosen and begin to sag or hang crookedly. It could be a huge problem, but the fix is usually quite simple. A simple tightening can resolve the issue. If the screw holes have been ripped out, it may be a challenge to complete. Fortunately, there is a trick to get these holes back to their original size using a wooden dowel.

Start by drilling out the old hole using a drill bit that is close to the size of the new screw (typically 3/8"). Fill in the hole with wood glue and a wooden stick. The dowel should be cut to a length that is exactly the same as the screw to ensure a snug fit. Reinstall the screw, and tighten to desired tightness. If the door does not stop bind up, add another dowel to the gap. Repeat the process. Close the door slowly after each adjustment to make sure that the clearances around the perimeter are correct.

You can also use a wooden plug instead of the dowel. It will work just as well but might take a bit longer to install. You can insert the wood piece that has been whittled down to the right size. If you don't have a tool for woodworking, you can also try using toothpicks or wooden matches.

Make use of a countersink in order to make the hole smaller for the head of the screw after you have reinstalled it. This will prevent the screw from hitting the edge of the doors as they are closed and opened. This will allow you to tighten the screw when you are reinstalling the hinge.

After installing the hinge, apply lubrication to the hinge using dry lubricant. This will prevent it from getting stuck in the future. You can use products such as PB Blaster and Liquid Wrench. You should apply a thin coat and give it approximately 15 minutes to reach the hinge barrel.

Refinishing the Hinges

If you're not ready to replace your hinges, try a few fixes. The first step is to make sure that the screws holding the hinge plate to the door and frame are tight. If they're loose, tighten them using a power drill or screwdriver. Be careful not to tighten your screws so much that they start to create gaps at the trim joints or, even more damagingly remove the threads.

If the problem is that the hinge plates are breaking away from the jamb and door it is possible to reattach them by gluing wood glue to the back of the plates and then inserting toothpicks or wooden dowels into the holes. The toothpicks and dowels provide a solid foundation for the screws, which will stop the plates from shifting as you drive them in. Allow the glue to dry before attaching the hinge.

The screws may also be damaged or missing. This can be corrected by replacing the screws. Be sure to use the correct drill bit for the size of the screw hole in order to avoid drilling into other parts of the hinge or jamb.

Close the door once you've reattached the hinge and measure the gap between the frame and the door. It should be around the thickness of one nickel all around or less if there's a gap that was caused by a previous door that was not properly hang. If the hinges were put in place correctly, this should not be an issue.

If the hinges still seem loose, you could add a thicker hinge between the hinge plate surface and the mounting surface. This will allow the hinges more room. You can also try removing the hinge pin from the problem hinge and then pounding it with a hammer in order to make it tighter or using the hinge pin from a different angle altogether. You can also grease your hinges with mineral oil or jojoba to reduce friction and help keep them in place. Lubricating your hinges regularly will help keep them from becoming stiff and squeaky, and also prolong their lifespan.

Cleaning the Hinges

A double glazed window hinge's continuous movement causes friction, which attracts dust particles. These particles may get stuck and accumulate over time in the moving parts of door hinges if they're not maintained and cleaned regularly. In the end the hinge becomes stiff and creaky, and its appearance can get worse. Regular cleaning, lubrication, and inspections will maintain the functionality and quality of hinges on a door.

Inspect the hinges to see how much rust has formed on their surfaces. If the rust has become so severe that it has damaged the surface of the screw holes or the barrel of the hinge, you'll have to replace them. If you're able to save the hinges, clean any loose rust by using steel wool and wire brush. Apply a commercial rust-removing solution or homemade solutions like lemon juice to the hinge. Allow the rust-removing solution to sit on the hinges for a few minutes to penetrate and dissolve any remaining rust.

If you don't wish to spend money and time replacing upvc window hinges your hinges, simply retightening the screws will restore the hinges' functionality. It is possible to attach a wooden shim or dowel to the hinge in the event that the screws have been degraded. Wooden dowels are round pieces of wood that are in the form of rods that are available in different sizes and lengths. They are available at home improvement centers as well as woodworking supply and craft shops, or on the internet.

You can also make an shim using metal or plastic depending on the type hinge you have. To make a dowel, you need to cut an unfinished dowel into the desired length. You can then dip a dowel in carpenter's glue and insert it in the hole. The glue will hold the dowel securely in place.

Before cleaning the hinges, put down a paper cloth or towel to shield your flooring from spills. After protecting the area then clean the hinges using a soft sponge or cloth coated with a mild cleaner to remove dirt and grime. Also, tarnish and rust can be removed. You can make use of a toothbrush or a small brush to get into difficult-to-reach areas in crevices or tight areas.