• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Most homeowners can repair window hinges a loose hinge. However, if the screw holes are damaged and won't hold screws you may need to put in wood glue and dowels before you can reinstall the hinge.

Before you do that, however you should clean off any the surface rust. This will allow the dowels to remain in place and provide them a solid base to hold onto.

Take off the Hinges

A variety of door hinges can be removed, making it simpler to move doors from one side of the frame to the opposite side or remove the entire door in the event of need. Anyone who is patient can take the hinges off, but you must be aware of what to do.

If the hinges have been painted you'll need to take off the paint before you attempt to remove the pins. If you don't, the paint will flake off and scratch the door when you attempt to lift it. Place the hinges in an stainless steel pot and fill it up with water to the point that the hinges are completely submerged. The hinges should remain in the pan for about 30 minutes. The heat from the water will soften the paint and make it easier to remove the pins.

Once the pins are loosened, remove the hinges and the frame from the window door repairs locks glass hinges. It is possible to use a standard screwdriver, however a magnetic screwdriver is recommended for this job. This type of screwdriver is specifically designed to grab screws made of metal and will help you get the job completed much quicker.

It is a good practice to spray lubricant on the hinges before attempting to remove them. A simple lubricant can help you to speed up the process and make the removal of pins and screws more easily. This type of lubricant can be found in most hardware stores as well as home improvement shops.

The number of hinges required will also differ based on the type of door you have, and how it's installed. Heavier and solid-cored doors will require more hinges, whereas lighter and hollow-cored doors may only require two or three hinges.

Understanding the different types of hinges will help you determine which one is best for your situation. Exterior hinges are designed to withstand the weight of a door, while hinges for interior use must be able support lighter loads.

Reattaching the Hinges

Sometimes a door hinge will loosen over time and start to hang crookedly or sag. This can be a problem, but it's usually easy to solve. In most cases it's a simple tightening of the screw will resolve the problem. If the screw holes have been stripped out, it can be difficult to fix. There is a method to make these holes back to their original size that uses a wood dowel.

Begin by drilling the old hole with a drill bit close to the size of the new screw (normally 3/8"). Fill in the hole using wood glue and a wooden stick. The dowel should be cut to a length exactly the same as the screw to ensure a snug fit. Then, reinstall the screw and tighten it to the desired level of tightness. If the door still has a tendency to bind, then add another dowel to the gap and repeat the process. Make sure to close the door slowly so that you can check the perimeter clearances after each adjustment.

Another option is to just utilize an old-fashioned wood plug instead of dowel. It works equally well, but may take a bit longer to set up. You can use a piece of wood that has been whittled down to the right size. If you don't own an instrument for woodworking or toothpicks, you can make use of toothpicks or wooden matchsticks.

Use a countersink to make the hole smaller for the head of the screw after you have reinstalled it. This will stop the screw from rubbing against the edges of the doors when they are closed and opened. This will make it much easier to tighten the screws after reinstalling hinges.

After you have reinstalled the hinge, be sure to grease it using a dry lubricant to ensure that it doesn't get stuck in the future. You can use products such as PB Blaster and Liquid Wrench. You should apply a thin coat and allow it to take around 15 minutes to fully get into the barrel of the hinge.

Refinishing the Hinges

If you are not ready to replace the buy upvc window hinges on your door, you are able to make a few minor repairs. Verify that the screws that hold the hinge plate to the door frame and the frame are in good condition. If they're loose, tighten them with a screwdriver or power drill. Be careful not to over tighten the screws, as this could create gaps at the trim joints, or worse, strip out the threads.

If the issue is that the hinge plates are separating from the door and jamb, you can reattach them by gluing wood glue to the plate's back and then inserting toothpicks or wooden dowels into the holes. Dowels and toothpicks create a solid foundation for the screws, which will stop the plates from shifting as you push them in. Allow the glue to dry before attaching the hinge.

The screws could also be stripped or missing. You can fix this problem by replacing the screws with longer ones. Make sure the drill bit is similar to the size of the screw hole to avoid drilling into the jamb or hinge.

After you've reattached your hinge close the door and check the gap between the door and the frame. It should be approximately the thickness of one nickel all around, or less if there's a gap caused by a previous door that was not properly hang. If the hinges were put in place correctly, this shouldn't be a problem.

If you find that the hinges are still loose, try adding a thicker hinge shim between the hinge plate and the mounting surface, to create an extra inch of space. You can also take off the hinge pin, then pound it down with a powerful hammer in order to tighten it or use a new window hinge repair cost. You can also lubricate the hinges using mineral or jojoba oil to reduce friction and assist in keeping their place. Lubricating your hinges frequently will stop them from becoming stiff and squeaky, and also extend their lifespan.

Cleaning the Hinges

The friction generated by the constant movement of a hinge attracts dust particles. Without periodic cleaning and lubrication, these particles get stuck in the moving parts of a door hinge and then build up over time. The hinge will get stiff and creaky, and its appearance could rapidly diminish. Regular cleaning, lubrication and inspection can help preserve the quality of a door's hinges and ensure their proper function.

Check the hinges to see how much rust has accumulated on their surfaces. If the corrosion has reached the point of destroying the surface of the hinge barrel or screw holes, you will need to replace the hinges. If you are able to save the hinges, you can remove any loose rust with a wire brush and steel wool. Then, apply an industrial rust remover or a homemade solution, such as lemon juice on the hinge. Let the solution that removes rust be on the hinges for a few minutes to penetrate and dissolve any remaining rust.

Retightening screws can restore hinge functionality If you don't wish to spend time or money to replace hinges. If you've sanded the screws' holes however, it might be necessary to attach the dowel of wood or shim to the hinge. Dowels made of wood are square pieces of wood that are in the form of rods, which are available in various sizes and lengths. They are available at home improvement stores or woodworking supply shops, or on the internet.

A shim could be made of plastic or metal, based on the type of hinge you've got. To make a dowel, cut a piece of wooden dowel or another sturdy material to the size you want. Then, dip a dowel into the adhesive of a carpenter and insert it in the hole. The glue will hold the dowel firmly in the desired position.

Before you begin cleaning the hinges, lay down a cloth or paper towel to protect flooring and other surfaces from drips and spills that could happen. After the area has been secured, proceed to clean the hinges using a soft sponge or cloth coated with a mild cleaner or vinegar to get rid of dirt, grime, and tarnish. You can make use of a toothbrush or a small brush to get into difficult-to-reach areas in crevices and tight areas.