• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Most homeowners can fix hinges that are loose. However, if the holes for screws are smashed and won't hold screws you may need to add dowels and wood glue before you can put back the hinge.

Before you do this, however you should clean off any surface corrosion. This will help the dowels stay in place and give them a solid foundation to rest on.

Eliminating the Hinges

Many standard door hinges can be removed, which makes it easier to move a door from one side of the frame to the opposite side or remove the entire door when needed. It is simple for anyone with a bit of patience, though you do have to know how to do it right.

If the hinges have been painted it is necessary to remove it before you attempt to remove the pins. You could scratch your door if you do not remove the paint. Place the hinges in the stainless steel pot and fill it with water to the point that the hinges are completely submerged. Let the hinges sit in the pan for about 30 minutes. The heat of the water will soften the paint, making it easier to remove.

Once the pins are loose, remove the hinges and frame from the door. It is possible to use a standard screwdriver, but a magnetic screwdriver is recommended for this task. This type of screwdriver is designed to grab screws made of steel and can make the work speed up.

It is a good idea to spray lubricant onto the hinges prior to trying to remove them. A simple lubricant can make the process move along quickly and make it easier to remove the pins and screws. This type of lubricant can be found in a variety of hardware stores and home improvement shops.

Keep in mind that the number of door hinges you will need will vary based on the type of repair door frame hinge side and its setting. Heavier and solid-cored doors will require more hinges whereas lighter and hollow-cored doors may only require two or three hinges.

It is also crucial to understand the different types of hinges to determine which ones be the most effective for your particular situation. Exterior hinges are generally designed to support the door's weight and interior hinges need to be able to support lighter loads.

Reattaching the Hinges

Over time the hinges on doors can become loose and start to slide or hang crookedly. It can be a big problem, but the Fix Door Hinge is usually simple. Retightening the screw will typically resolve the issue. If the screw holes have been stripped out, it may be difficult to do. There is a method to make these holes tight again that utilizes a wood dowel.

Begin by drilling the old hole with a drill bit close to the new screw size (normally 3/8"). Fill in the hole with wood glue and a wooden stick. To ensure a secure fit, the dowel must be cut to the same length as the screw. Reinstall the screw and tighten it until you are satisfied with the level of tightness. If the door still has an tendency to get stuck, then add another dowel to the gap and repeat the process. Make sure to close the door slowly so that you can verify the clearances at the perimeter after each adjustment.

You could also use a wood plug in place of the dowel. It works just as well but might take a bit longer to set up. You can use a piece of wood that has been whittled to the proper size. If you don't have a wooden tool you could also try using toothpicks or wooden matches as well.

Once you have reinstalled the new screw, use a countersink bit to make the hole for the screw's head smaller, so that it doesn't rub against the edge of the door when it's opened and closed. This will make it easier to tighten the screw prior to installing the double glazing hinge repairs.

After installing the hinge again, you should lubricate the hinge with a dry lubricant. This will help prevent it from becoming stuck in the future. Products such as PB Blaster or Liquid Wrench are good options. Apply a thin layer and allow it to penetrate the hinge barrel for about 15 minutes.

Refinishing the Hinges

If you're not ready to replace the hinges on your door, you can make a few repairs. The first step is to check that the screws holding the hinge plate to the door frame are tight. If they are loose, tighten the screws using a power drill or screwdriver. Be careful not to over tighten the screws, because this could create gaps at the trim joints, or more seriously, tear out the threads.

If you're experiencing issues because the hinge plates are separating from the door and jamb it is possible to reattach them by applying wood glue to the plate's back and then inserting toothpicks or wooden dowels into the holes. Dowels or toothpicks will give a solid foundation for the screws and help to prevent the plates from shifting when you drive them into position. Allow the glue to dry before attaching the hinge.

Another common cause of loose hinges is that the screws are damaged or missing. This problem can be fixed by replacing the screws. Make sure the drill bit is exactly the same size as the screw hole to prevent drilling into the hinge or jamb.

Close the door once you've reattached the hinge and measure the gap between the frame and the door. The gap should be the thickness of a penny all around or less if an old door was not properly hung. This should not be a problem as long as the replacement double glazing hinges are installed correctly.

If you discover that the hinges are loose, you can try adding the thicker shim of the hinge between the hinge plate and the mounting surface, to create a little extra space. You can also take off the hinge pin, then pound it down with a heavy hammer to tighten it up or choose the hinge of a different type. You can also lubricate the hinges using mineral or jojoba oil to reduce friction and assist in keeping their place. Lubricating your hinges regularly can help keep them from becoming stiff or squeaky, and will also extend their life.

Cleaning the Hinges

The constant movement of a hinge creates upvc friction hinges, which attracts dust particles. If there is no regular cleaning or lubrication, the particles become stuck in the moving parts of a door hinge and then build up over time. In the end the hinge becomes stiff and creaky, and its appearance can deteriorate rapidly. Regular cleaning, lubrication and inspection can help preserve the quality of door's hinges and ensure their proper operation.

Examine the hinges for signs of corrosion. If the rust has become so severe that it has damaged the surface of the screw holes or the barrel of the hinge, you'll have to replace the hinges. If you are able to save the hinges, clean any loose rust by using wire brush and steel wool. Then, apply an industrial rust remover or homemade solution like lemon juice to the hinge. Let the rust remover sit on the hinge for several minutes to penetrate and dissolve any remaining corrosion.

If you don't wish to spend the money and time replacing your hinges, simply retightening the screws will make the hinges functional again. It is possible to attach dowel or shim made of wood to the hinge in the event that the screws have been shaved. Dowels made of wood are available in round rods of varying lengths and sizes. They can be purchased online, at woodworking supply shops and at home improvement stores.

A shim can also be made from plastic or metal, depending on the type of hinge you have. To make a dowel cut a dowel from wood to the desired length. You can then dip the dowel into carpenter's glue before inserting it into the stripped hole, allowing the glue to hold the dowel in place.

Before you start cleaning the hinges, place down a paper or cloth towel to shield flooring and other surfaces from spills and drips that may happen. After the area has been secured and dry, clean the hinges with an absorbent sponge or a soft cloth coated with a mild cleaner or vinegar to remove dirt, grime, and tarnish. You can make use of a small or toothbrush brush to reach hard-to-reach spots in tight spaces handles and hinges crevices.