• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Choosing Upvc Window Replacement Hinges

It's not as difficult as it may appear to select and install upvc replacement hinges. It is essential to verify that the arrow on the hinges are facing in the correct direction and the thickness (13mm or 17mm) of the hinge arm on the opening frame.

There are several different types of hinges, each having their distinctive characteristics. This article will go over the most popular uPVC hinges, as well as their benefits.

Egress/Easy Clean Hinge

They are an excellent choice for replacing or upgrading a fire escape safety window, as they open at a full 90-degree angle. They can be disengaged to an easy-clean position that allows you to see the outside of windows without the need to climb ladders or lean over dangerous angles.

These heavy-duty egress hinges are manufactured by Yale which is among the most popular and respected home security brands available today. These hinges are compatible with any type of uPVC side-hung window. By pressing a small button the window sash is slid to the side and into the easy-cleaning position. Once closed, the sash will automatically reset to its original operative position.

They are available in 13mm and 17mm stack heights. Based on the size of your existing window, we recommend using our Egress Selection Guide to determine which product is best for you.

The hinges are designed to work with standard side-hung frames which is made of aluminum or uPVC. The friction screw is used to adjust the resistance. This makes opening the windows easier and reduces the chances of accidental closing during high winds. They have been cycle tested to over 30000 cycles and are in compliance with BBA/Secured by Design and British Standards approved BS EN 13126-6:2008.

There are no buttons or catches The Nico Egress Easy Clean Friction Hinge is easy to use and provides a convenient solution to emergency egress as well as safe cleaning. Firstly, open the window to the egress (full opening) position and then press the hinge retaining clip on the inside of the bottom corner. This will open the top and bottom catches, allowing you to slide the sash into an easy-clean position. Once you are in the clean position close the pvc window hinges to reset the hinges to their egress position.

Fire-Escape Hinge

Fire Escape Hinges, often known as "Easy Clean" hinges are used to replace side-opening windows for egress (fire safety) reasons. These kinds of hinges for windows open more wide and faster than normal hinges, allowing an expansive clear opening to escape in the event of an incident of fire. The building regulations state that this type of hinge should be placed in any room that has a window.

They feature an exclusive friction stay that allows the window to open at an angle of 90 degrees. It also allows the sash opening to slide across when open for easy cleaning of the exterior side of the glass to glass hinges, without having to climb ladders. The hinges have no fiddly buttons or catches, and are operated with an easy, secure lever that is accessible from the inside of the home.

The hinges are made in the UK by Cotswold and come with a child safety limiter for day-to-day use which can be turned off by a hidden button, giving you peace of mind that your children will not accidentally open the door hinge repair too far. The stack heights are 13mm or 17mm.

To order these hinges, simply measure the length of your current side-hung window hinge that is fixed to the frame (see the article on measuring your upvc window hinges). Then select the correct size hinge from the selections below.

Please note that this measurement is taken at the hinge's part that attaches to the frame, not the sash. The actual hinge length may be shorter or longer depending on how your old windows were manufactured. Also, when choosing the width of your hinge, most upvc windows will fit 13mm stack height, however should your old frame is 17mm wide, you should select the option to use this. You can also opt for the 4mm packer in order to make up the difference. All hinges are in two different directions (1 left and one right). The hinges are not equipped with screws. If needed, they can be purchased separately. We recommend using our upvc window hinge repair screws. These screws are designed to enhance the performance of your hinges and allow them to work smoothly for longer. They feature a less friction design and a better weather seal with a new nylon reducer end cap.

Restricted Hinge

There are occasions when windows must fully open and this can be difficult using a standard hinge. These child safety friction hinges are a great way to solve this problem. They can be used when ventilation is required but escaping or cleaning an fire isn't feasible. They restrict the amount of opening the sash, and allow overriding this limitation by pressing an appropriate button. They are available in 13mm or 17mm stack heights. They can be used for both top and side hung windows.

The Nico Restricted Egress Friction Hinges combine the features of both a standard restrictor and a pivot for fire escape to provide a simple but efficient method of complying with building regulations. It is suitable for side hung and top opening uPVC windows and comes in 17mm and 13mm stack heights. It is offered in a pair, where one hinge is the restricted egress, the other unrestricted allowing one of these to be placed to the bottom of the sash whilst the other is attached to the top.

These uPVC restrictive hinges have been tested to BS6375 part 2 and are designed for use on a window that cannot be fully opened like a small child's bedroom. The mechanism restricts how far the sash can open to an appropriate height of 100mm, and re-engages once the window is shut.

These uPVC friction-type hinges can be used with all types of windows. They are especially useful for windows that are difficult to reach, like those in three-storey apartments or those which would require the use of a ladder. They can be paired with our selection of security enhancements such as hinge guards, protection plates for hinges or dog bolts to provide PAS 24 performance.

When replacing a Window Door Repairs Locks Glass Hinges hinge it is essential to measure the length of the current hinge so that you can order replacements that match in size. This can be done by looking through the image gallery of the hinge before deciding where you would like it to be. Top hung hinges can be restricted on both sides and the side hung hinges can only be used only on one side.

Standard Hinge

A standard hinge is made of metal-to-metal contact, and there are no additional components to reduce friction. It is available in many finishes and also has a fire rating. To determine the radius of your hinge lay it flat and then line up the quarter and dime in two corners. If the dime fits better and the corner is round by 1/4 inch. If the quarter fit better, it's rounded to 5/8 inch.

Choosing the right type of hinge can make or break the appearance of your double glazing door hinges. It's important to match the style and finish of your door with the hinges to create a unified appearance that is both practical and visually appealing.